|
| Merknaam: | Phidix |
| Modelnummer: | aangepast |
| MOQ: | 100 stuks |
| Prijs: | $20.00/pieces |
[Push-Pull Standard Control Cable Assembly]
Description: Applications: Features:
Push-Pull Standard • Implement control • Typical temperature range
Industrial Control • Throttle control -65°F — 230°F (Bristow)
Cable Assembly • PTO/4WD activation -65°F — 230°F (Utility)
• Valve actuation -65°F — 230°F (Low Friction EXT)
• Remote battery disconnect -65°F — 230°F (Low Friction)
• Remote electrical disconnect • Tough/durable materials
• Transmission shift • Long lasting seals
• Hydrostatic drives • Environmentally protected
• Latches
Material: End Fittings
• Stainless Steel or • Full Range
Plated Carbon Steel
• Plastic Coated
Carbon Steel
Conduit and
Innermember
• Plastic Seals
[Push-Pull Industrial]
We offer a full range of push-pull controls that provide a means of transmitting linear motion from one location to another. They offer ease of installation as well as superior performance.
The Bristow® Type control is an economical construction for applications which do not require tight bend radii, and are temperature rated for use from a low of -65°F to a peak of +230°F.
The Utility Style adds a binder wire for structural integrity and a tighter minimum bend radius than other controls.
Low Friction EXT controls have the same advantages as utility with an added plastic covered innermember which provides improved efficiency.
Low Friction controls provide the standard of excellence for industrial controls. Features include a binder wire for structural integrity, tight minimum bend radius, and PTFE covered innermember for the ultimate in efficient, smooth operation. Temperature rated for use from a low of -65°F to a peak of +230°F, they will provide long life in the most demanding applications.
[Push- Pull Standard Description]
Design — We have a wide variety of industrial, ordnance, marine and aircraft applications. Combined with careful selection of materials and fabrication methods, this design provides users the most versatile, highest quality control available today.
End Rod and Support Tube — All standard controls may be ordered with either type 300 stainless steel or protectively plated carbon steel end rods and support tubes. Choose the material to best meet your requirements.
End Rod Seals — Rod wiper seals have been carefully designed to prevent entry of moisture and contamination into the support tube and to provide a bearing surface for smooth motion of the end rod. Two types of rod wiper seals are available (see seal options in ordering code), capable of meeting a wide range of environmental conditions.
Improved Model 5 Floating Wiper Seal — All Utility, Low Friction, Low Friction EXT and Bristow® controls are equipped with the new improved molded plastic Model 5 seal unless otherwise specified. Extensive testing and field experience have proven the ability of this seal to protect the control in contaminated environments. Security tabs hold the seals in position and an internal support tube bushing improves end rod alignment.
Model 6 Floating Wiper Seal System — The Model 6 seal system is offered as an option on all Push-Pull control cables. It is designed to provide a tighter fit with the surface of the rod end and an internal o-ring is added at the swivel joint of the support tube for additional protection. The Model 6 seal system provides additional sealing for use in extreme environmental conditions. Because this seal produces additional load friction to a push-pull control cable, it is recommended for applications which can tolerate extra friction.
Swivel — The swivel joint between support tube and end cap is designed to allow 8 degrees minimum swivel from the control centerline.
Swivel Seal — Protection of the swivel joint from entry of moisture and contamination is provided by a molded seal. On LD and larger sizes, mounting nuts for threaded type conduit fittings may be removed without removing the swivel seal.
Conduit Caps — All standard controls have plated steel conduit fittings. Special controls designed for marine and aircraft applications are available with stainless steel or brass fittings.
Conduit — Four types of conduit construction are available to meet various requirements — Low Friction, Low Friction EXT, Utility and Bristow. These standard conduits are covered with a tough plastic casing for protection against corrosion and abrasion. Color coding of the casings allows easy identification of the control type:
Low Friction-Green
Low Friction EXT-Green
Utility-Gray
Bristow-Black
Inner Operating Member — The inner operating member for all standard controls is made of flexible 1 X 19 strand, armored with a swaged steel jacket for efficient operation and compression strength. Stainless steel inner operating member is available for added protection in corrosive environments. In Low Friction controls, a coating of PTFE provides superior efficiency and reduces “stick-slip” during operation. Note: VLD Bristow is a solid wire, Low Friction EXT is plastic covered, Utility is uncovered.
Lubrication — All standard controls are lubricated during construction with carefully selected compounds to provide optimum performance. No further service is necessary or recommended.
Installation — Mechanical stops should be implemented at or below the travel desired (ie. 1,2, 3, 4, 5, or 6) on the equipment on which the cable assembly is being installed. Internal damage may result if end rod is allowed to bottom inside conduit cap.
[Push-Pull Standard Specifications]
All line art dimensions are represented in inches
[Push- Pull Standard Order Code]
Phidix Motion Controls (PMC) started the business in 2004, and became the only authorized Cable Assembler in China by the American based company Cablecraft Motion Controls (CMC) in 2011.
CMC was originally a subsidiary of Tuthill Group (more than 100 years history), headquartered in New Haven Indiana US and became independent in 2011. CMC can offer diverse high-end drive control products and engineering solutions. The product line includes control flexible shaft of the various specifications, cab units and a category range of standard parts, widely used in high-end industrial customer markets, such as luxury bus, heavy truck, aerospace, construction machinery, rail transportation, agricultural machinery, gardening equipment, racing cars, military vehicles, tanks etc. as selection of shift control, throttle cable, clutch cable, brake line, valve and other mechanical transmission controls.
Just after CMC became the independent group in 2011, PMC became the only authorized Assembler in China responsible for the manufacturing, assembly, sales, technical support, after-sales service of control items from CMC, acted as the multi-functional management and development center (PMDC) for the R&D of creative control technology, parts manufacturing, cable assembly and the import and export business as well.
Today, thousands of personalized products designed and produced by PMC in China are selling to all over the world.
If you are interested in our products,please tell us which model,quality you want to order.
A performa invoice will be made for your order.
We will deliver the product ASAP when we receive your payment.
Please contact us without hesitation, we are pleased to welcome to you!!!
PHIDIX MOTION CONTROLS(SHANGHAI) CO.,LTD
Add: Building #21, Block 9299, Tingwei Road, Jinshan District, Shanghai 201505
Tel: (86-21)37214606/ 07/ 08/ 09
Fax: (86-21)37214610
MP: 13816744282
Website: www.mechanical-controlcable.com
E-mail: info @phidixglobal.com
Please find our on-line catalogue by
https://phidixglobal.en.alibaba.com/productlist.html?spm=a2700.8304367.topnav.2.42d9fe5aBxe8Bj
